Graco Webcam 3A1324B User Manual

Instructions/Parts  
16G351 Electric Power  
Conversion Kit  
3A1324B  
EN  
Converts ProMix 2KE Electronic Proportioners from an intrinsically safe air-powered  
alternator power supply to a non-intrinsically safe electric power supply.  
For professional use only.  
Not approved for use in European explosive atmosphere locations.  
Important Safety Instructions  
Read all warnings and instructions in this  
manual and your separate ProMix 2KE  
manuals. Save these instructions.  
Converting the ProMix 2KE proportioner from an  
air-powered alternator power supply to an electric  
power supply voids the intrinsically safe rating of the  
equipment.  
Kit Parts  
Ref. Part  
Description  
Qty.  
401 15V747 POWER SUPPLY, 24 VDC, 2.5 A,  
60 watt, B-code  
402 116320 SWITCH, rocker, power  
403 115306 FILTER, power line  
1
1
1
1
4
2
2
1
1
1
1
404 114095 BLOCK, terminal  
405 112144 SCREW, machine, pan head  
406 109467 SCREW, machine, pan head  
407 103833 SCREW, machine  
408 100139 PLUG, pipe  
410 16H077 HARNESS, 2-wire; 8 in. (203 mm)  
411 16H078 HARNESS, 3-wire; 4 in. (102 mm)  
413 15V206 CABLE, CAN; 10 ft (3 m)  
 
Remove the Alternator  
Remove the Alternator  
4. Systems with a USB Module: Disconnect and  
save the cable (412) that runs from the AFCM to the  
alternator.  
1. Shut off the system’s main air valve. Open the con-  
trol box.  
5. Disconnect air regulator line and exhaust air line  
from alternator module. Remove air regulator  
assembly (R) from solenoid manifold (M). Install  
plug (408) from kit in the open manifold port.  
2. See FIG. 1. Disconnect output power cable connec-  
tions from alternator module (A). Disconnect ground  
lead (G) from control box ground terminal (T).  
6. Remove four screws (S) from mounting to remove  
alternator from control box.  
3. Disconnect the power supply cables from the  
Advanced Fluid Control Module (AFCM),  
USB Module, and Display Module.  
T
Air regulator  
line  
A
Cable  
A
connectors  
R
ti16455a  
ti16456a  
M
Install plug (408)  
in open port  
G
S
Air exhaust  
line  
FIG. 1. Remove Alternator Module  
3A1324B  
3
 
 
Install the Kit  
Install the Kit  
Component Installation  
1. Shut off electrical power at the main panel.  
5. Connect the power supply wire harness (PS) to the  
switch (402), as shown. See also FIG. 6, Electrical  
Schematic. Connect the PS ground wire to the  
ground terminal (T) of the control box.  
2. See FIG. 2. Remove the square knockout in the side  
of the control box. Install the power switch (402).  
3. Install the power supply (401), line filter (403), and  
terminal block (404), using supplied screws (405,  
407, 406), as shown.  
6. See FIG. 5. Connect wire harness (411) to the line  
filter (403) and terminal block (404), as shown. See  
also FIG. 6, Electrical Schematic.  
4. See FIG. 2. Connect wire harness (410/LF) to the  
line filter (403) and switch (402), as shown. See also  
FIG. 6, Electrical Schematic.  
402  
2: PS(L)  
2A: LF(L)  
1: PS(N)  
1A: LF(N)  
FCM  
T
C
LF(L)  
LF(N)  
405  
401  
PS(N)  
410  
403  
PS(L)  
407  
406  
PS(GND)  
411 (see FIG. 5)  
404  
ti16454b  
FIG. 2. Install Power Supply Kit  
4
3A1324B  
 
 
Install the Kit  
Install the Power CAN Cables  
Systems with a USB Module  
Systems without a USB Module  
1. See FIG. 3. Connect cable (413) to J6 of the display  
module and to connector P3 of the USB module.  
1. See FIG. 4. Connect cable (413) to J6 of the display  
module and to J8 of the Advanced Fluid Control  
Module.  
2. Connect saved cable (412) to connector P4 of the  
USB module and to J8 of the Advanced Fluid Con-  
trol Module.  
2. Connect the power supply CAN cable (C, FIG. 2) to  
J7 on the Advanced Fluid Control Module (FIG. 4).  
3. Connect the power supply CAN cable (C, FIG. 2) to  
J7 on the Advanced Fluid Control Module (FIG. 3).  
Display Module  
4. See your ProMix 2KE Operation manual for instruc-  
tions on using the USB module.  
USB Module (if present)  
TI16604a  
P4  
Connect cable  
(412) here  
P3  
J6  
Connect cable  
(413) here  
Connect cable (413) here  
TI16580a  
Advanced Fluid Control Module  
Display Module  
J8  
Connect  
cable  
J7  
Connect  
cable (C)  
here  
TI16604a  
(413) here  
J6  
Connect cable (413) here  
TI16579a  
TI16602a  
Advanced Fluid Control Module  
FIG. 4. Install Power CAN Cables (without USB  
Module)  
J8  
Connect  
cable  
J7  
Connect  
cable (C)  
here  
(412) here  
TI16579a  
TI16602a  
FIG. 3. Install Power CAN Cables (with USB Module)  
3A1324B  
5
 
 
Install the Kit  
Power Connection  
All electrical wiring must be completed by a qualified  
electrician and comply with all local codes and  
regulations.  
Enclose all cables routed in the spray booth and high  
traffic areas in conduit to prevent damage from paint,  
solvent, and traffic.  
411  
404  
The ProMix 2KE operates with 85-250 VAC, 50/60 Hz  
input power, with a maximum of 2 amp current draw.  
The power supply circuit must be protected with a 15  
amp maximum circuit breaker.  
Line  
Not included with kit:  
Neutral  
Ground  
Power supply cord compatible to your local power  
configuration. Wire gauge size must be 8-14 AWG.  
ti16391a  
FIG. 5. Terminal Block Electrical Connections  
The input power access port is 22.4 mm (0.88 in.) in  
diameter. It accepts a bulkhead strain relief fitting or  
conduit.  
1. Verify that electrical power at the main panel is shut  
off.  
TERMINAL  
BLOCK  
2. Connect electrical cord to the terminal block (404)  
as shown in FIG. 5.  
L
L
N
GRND  
WIRE  
HARNESS  
(411)  
3. Close the Control Box. Restore power.  
POWER  
SUPPLY  
N
GRND  
N
4. Follow instructions in Grounding in your ProMix  
LINE POWER  
FILTER  
2KE Operation Manual.  
L
5. See your ProMix 2KE Operation manual for operat-  
ing instructions.  
WIRE  
HARNESS  
(410)  
2A  
2
1A  
SWITCH  
ROCKER  
1
POWER SUPPLY  
WIRE HARNESS  
GRND  
FIG. 6. Electrical Schematic  
6
3A1324B  
 
   
Install the Kit  
3A1324B  
7
 
Graco Standard Warranty  
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in  
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty  
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by  
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written  
recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty  
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of  
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with  
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or  
maintenance of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of  
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned  
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will  
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED  
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy  
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or  
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.  
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT  
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to  
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these  
warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or  
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the  
negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,  
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la  
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite  
de ou en rapport, directement ou indirectement, avec les procédures concernées.  
Graco Information  
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.  
Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
Original instructions. This manual contains English. MM 3A1324  
Graco Headquarters: Minneapolis  
International Offices: Belgium, China, Japan, Korea  
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA  
Copyright 2010, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.  
Revised 08/2011  
 

HANNspree Flat Panel Television K212 10H1 User Manual
Harbor Freight Tools High Chair 91090 User Manual
Harbor Freight Tools Saw 91852 User Manual
Honeywell Heating System L8124A User Manual
Hotpoint Cooktop LI2I2A User Manual
Hotpoint Dishwasher HDA965 User Manual
Hotpoint Washer Hotpoint Washing Machine User Manual
HP Hewlett Packard Digital Camera M22 User Manual
HP Hewlett Packard Server 545740 002 User Manual
HP Hewlett Packard Server BL495c User Manual