Gas Hob
IZGS 68 ICTX
EG
Thank you for selecting our appliance
We wish you lots of enjoyment with your new appliance and we hope that you will
consider our brand again when purchasing household appliances.
Please read this user manual carefully and keep it throughout the product life cycle
as a reference document. The user manual should be passed on to any future owner
of the appliance.
2
Contents
For the User
Important Safety Information ............................................................................. 4
Description of the appliance .............................................................................. 6
Operation .......................................................................................................... 7
Using the hob.................................................................................................... 8
Cleaning and Maintenance ................................................................................ 9
Service and Original Spare Parts ..................................................................... 19
For the Installer
Technical data ................................................................................................. 10
Installation ....................................................................................................... 12
Gas Connection .............................................................................................. 13
Electrical Connection....................................................................................... 15
Building In ....................................................................................................... 17
Possibilities for insertion .................................................................................. 18
Guide to Use the instructions
The following symbols will be found in the text to guide you throughout the
Instructions:
Safety Instructions
Step by step instructions for an operation
Hints and Tips
Environmental information
This appliance complies with the following E.E.C. Directives:
• 2006/95 (Low Voltage Directive);
• 2004/108 (Electromagnetical Compatibility Directive);
• 90/396 (Gas Appliances) and subsequent modifications.
MANUFACTURER :
ELECTROLUX ITALIA S.p.A.
C.so Lino Zanussi, 30
33080 Porcia (PN) - ITALY
These instructions are only for the countries stated by the symbol printed on
the front cover of this instruction book.
3
English
Important safety information
This warnings has been given for the safety of you and others. We therefore
ask you to carefully read the procedures of installing and using this cooker.
contact with it and keep them far
enough from the heated parts of this
appliance.
Installation
The work of installation must be
carried out by competent and qualified
installers according to the regulations
in force.
• If the appliance is out of order,
disconnect it from the electric supply.
• Any modifications to the domestic
electrical mains which may be
necessary for the installation of the
appliance should be carried out only
by competent personnel.
People Safety
• This appliance has been designed to
be operated by adults and children
under supervision. Young children
must not be allowed to tamper with the
controls or play near or with the oven.
During Operation
• This appliance is not intended for use
by children or other persons whose
physical, sensory or mental capabilities
or lack of experience and knowledge
prevents them from using the
appliance safely without supervision or
instruction by a responsible person to
ensure that they can use the appliance
safely.
• Accessible parts of this appliance may
become hot when it is in use. Children
should be kept away until it has
cooled.
• This appliance has been designed for
non professional purpose in private
houses only. It is meant to cook edible
foodstuff only and must not be used
for any other purposes.
• It is dangerous to alter the specification
in any way.
• For hygiene and safety reasons, this
appliance should be kept clean at all
times. A build-up of fats or other
foodstuff could result in a fire.
• Under no circumstances should you
attempt to repair the appliance
yourself. Repairs carried out by
unexperienced persons may cause
injury or serious malfunctioning. Refer
to your local Service Centre. Always
insist on genuine spare parts.
About Installation, Cleaning and
Maintenance
It is mandatory that all operations
required for the installation are carried
out by a qualified or competent
person, in accordance with existing
rules and regulations.
• Ensure that all control knobs are in the
OFF position when not in use.
• Should you connect any electrical tool
to a plug near this cooking appliance,
• Disconnect the appliance from the
electrical supply, before carrying out
any cleaning or manteinance work.
ensure that electric cables are not in • Ensure a good ventilation around the
4
appliance. A poor air supply could
cause lack of oxygen.
• Ensure that the gas supply complies
with the gas type stated on the
identification label, placed near the gas
supply pipe.
Environmental Information
After installation, please dispose of
the packaging with due regard to
safety and the environment.
• When disposing of an old appliance,
make it unusable, by cutting off the
cable.
• This appliance is not connected to a
combustion products evacuation
device. It must be installed and
connected in accordance with current
installation regulations. Particular
attention shall be given to the relevant
requirements regarding ventilation.
• The use of a gas cooking
appliance results in the production
of heat and moisture in the room in
which it is installed. Ensure that
the kitchen is well ventilated: keep
natural ventilation holes open or
install a mechanical ventilation
device (mechanical extractor
hood).
• Prolonged intensive use of the
appliance may call for additional
ventilation, for example opening of
a window, or more effective
ventilation, for example increasing
the level of mechanical ventilation
where present.
The symbol
on the product or
on its packaging indicates that this
product may not be treated as household
waste. Instead it shall be handed over to
the applicable collection point for the
recycling of electrical and electronic
equipment. By ensuring this product is
disposed of correctly, you will help
prevent potential negative consequences
for the environment and human health,
which could otherwise be caused by
inappropriate waste handling of this
product. For more detailed information
about recycling of this product, please
contact your local city office, your
household waste disposal service or the
shop where you purchased the product.
• Once you removed all packaging from
the appliance, ensure that it is not
damaged and the electric cable is in
perfect conditions. Otherwise, contact
your dealer before proceeding with the
installation.
• The manufacturer disclaims any
responsability should all the safety
measures not be carried out.
It is very important that this
instruction book should be kept
safely for future consultation. If
the appliance should be sold or
given to another person, please
ensure that the booklet goes
together with it, so that the new
owner can know of the functions
of the machine and also be aware
of the warnings.
Service
• Under no circumstances should you
attempt to repair the appliance
yourself. Repairs carried out by
unexperienced persons may cause
injury or serious malfunctioning. Refer
to your local Service Centre. Always
insist on genuine spare parts.
5
Description of the appliance
2
2
3
1
4
1
2
3
4
Auxiliary burner
Semi-rapid burner
Triple crown burner
Control knobs
6
the "off" position and wait for
at least 1 minute before trying
to light the burner again.
Operation
Hob burner control knobs
To switch off burners
The symbols on the knobs mean:
= no gas supply
To put the flame out, turn the knob to
the symbol ().
= maximum gas supply
Take care when frying food in
hot oil or fat, as the overheated
splashes could easily ignite.
= minimum gas supply
When switching on the mains, after
installation or a power cut, it is quite
normal for the spark generator to be
activated automatically.
Foreasierlighting, proceedbefore
putting a pan on the pan support.
Lighting the burners
To light a burner, turn the relevant
knob anticlockwise to maximum
position (
to ignite.
) and push down the knob
After lighting the flame, keep the
knob pushed down for about 5
seconds. This will allow the
"thermocouple" to be heated and the
safety device to be switched off,
otherwise the gas supply would be
interrupted. Then, check the flame is
regular and adjust it as required.
If you cannot light the flame even
after several attempts, check the "cap"
and “crown” are in the correct position.
In the absence of electricity, ignition
can occur without the electrical device;
in this case approach the burner with a
flame, push the relevant knob down and
turn it anti-clockwise until it reaches the
"maximum" position.
A - Burner cap
B - Burner crown
C - Ignition candle
D - Thermocouple
Triple crown
A
B
Do not keep the control knob
pressed for more than 15
seconds. If the burner does not
light even after 15 seconds,
release the control knob, turn
it the "off" position and wait for
at least one minute before
trying to light the burner again.
If the burner accidentally goes
out, turn the control knob to
D
C
7
Using the hob correctly
Practical hints
The burners
To ensure maximum burner • If the control knobs become difficult to
turn, please contact your local Service
Force Centre.
• As soon as a liquid starts boiling, turn
down the flame so that it will barely
keep the liquid simmering.
efficiency, you should only use pots and
pans with a flat bottom fitting the size of
the burner used.
Triple Crown Burner
diameter 18-26 cm
Front Semi-rapid Burner
diameter 12-18 cm
Rear Semi-rapid Burner
diameter 12-22 cm
Auxiliary Burner
diameter 8-16 cm
• For easier lighting, proceed before
putting a pan on the pan support.
• Use only pans or pots with flat bottom.
• Take care when frying food in hot
oil or fat, as the overheated
splashes could easily ignite.
• If you use a saucepan which is smaller
than the recommended size, the flame
will spread beyond the bottom of the
vessel, causing the handle to overheat.
• Prolonged
cooking
with
potstones, earthenware pans or
cast-iron plates is inadvisable.
Also, do not use aluminium foil to
protect the top during use.
• Make sure pots do not protrude over
the edges of the cooktop and that they
are centrally positioned on the rings in
order to obtain lower gas
consumption.
• Do not place unstable or deformed
pots on the rings: they could tip over or
spill their contents, causing accidents.
• Pots must not enter the control
zone.
8
Cleaning and Mainteinance
Disconnect the appliance from
the electrical supply, before
carrying out any cleaning or
manteinance work.
The hob is best cleaned whilst
it is still warm, as spillage can
be removed more easily than if
it is left to cool.
This appliance cannot be
cleaned with steam or with a
steam cleaning machine.
The burners
The burner caps and crowns can be
removed for cleaning.
Wash the burners taps and crowns
using hot soapy water, and remove
marks with a mild paste cleaner. A
well moistened soap impregnated
steel wool pad can be used with
caution, if the marks are particularly
difficult to remove.
After cleaning, be sure to wipe dry
with a soft cloth.
Frequently wash the "caps" and the
"crowns" with hot soapy water,
carefully taking away any built-up of
food.
YES
NO
The pan supports
The pan supports are not
dishwasher proof; they MUST be
washed by hand.
After cleaning, make sure that the
pan supports are correctly
positioned.
To make burners work properly,
ensure that pan supports are placed
in a way that the arms are centred
upon the burner as shown in the
picture.
Pay attention when replacing the
pan supports in order to avoid
damaging the hob top.
9
The Hob Top
Regularly wipe over the hob top
using a soft cloth well wrung out in
warm water to which a little wasing
up liquid has been added. Avoid the
use of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for
non-stick saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily
soiled, the following products are
recommended:
- For stainless steel hobs use a
proprietary stainless steel cleaner.
- For other hobs use Hob Brite or Bar
Keepers Friend.
Do not leave acid or alkaline
substances (e.g. vinegar, salt,
lemon juice, etc.) on the cooktop.
The Ignition electrode
The electric ignition is obtained
through a ceramic electrode with a
metal electrode inside (Fig. page 7 - C).
Keep these components very clean, to
avoid difficult lighting, and check that
the burner crown holes (Fig. page 7 - B)
are not obstructed.
10
Technical data
Cut out dimensions
(see chapter “Building In”)
Width:
Heat Input
Triple Crown burner
Semi-rapid burner
Auxiliary burner
4,0 kW
2,0 kW
1,0 kW
560 mm
480 mm
Depth:
Overall dimensions
Electric supply:
Category:
230 V ~ 50 Hz
II2H3+
Width:
Depth:
594 mm
510 mm
Gas supply:
Appliance class
LPG 28-30 / 37 mbar
3
BURNER
NORMAL
POWER
kW
REDUCED
POWER
kW
NORMAL POWER
NATURAL POWER
LPG
28-30/37 mbar
m3/h
g/h
inj.
inj.
G20
G30
73
G31
71
100/mm
20 mbar
100/mm
Auxiliary
1,0
2,0
4,0
0,33
0,45
1,2
70
96
0,095
50
Semi-rapid
Triple crown
0,190
0,381
71
98
145
291
143
286
146
By-pass diameters
Burner
Ø By-pass in 1/100 mm.
Auxiliary
28
32
56
Semi-rapid
Triple crown
11
Installation
The following instructions about
installation and maintenance must
be carried out by qualified
personnel in compliance with the
regulation in force.
The appliance must be electrically
disconnected
before
all
interventions. If any electric supply
to the appliance is required to
carry out the work, ensure all the
necessary precautions are
followed.
The side walls of the unit in which
the hob is going to be installed,
must not exceed the height of the
working top.
Avoid installing the appliance in
the proximity of inflammable
materials (e.g. curtains, tea towels
etc.).
THE MANUFACTURER WILL NOT
ACCEPT LIABILITY, SHOULD ANY OF
THE OTHER SAFETY INSTRUCTIONS
INCORPORATED IN THIS BOOKLET
OR THE REGULATION IN FORCE BE
IGNORED.
12
Gas Connection
Connection to the gas supply should be
with either rigid or semi-rigid pipe, i.e.
steel or copper.
The connection should be suitable for
connecting to RC 1/2 (1/2 BSP male
thread).
Important
When the final connection has been
made, it is essential that a thorough leak
test is carried out on the hob and
installation. Use some soapy water,
never a flame.
Ensure that the main connection pipe
does not exert any strain on the hob.
A) End of shaft with nut
B) Washer
C) Elbow
It is important to install the elbow
correctly, with the shoulder on
the end of the thread, fitted to the
hob connecting pipe.
Failure to ensure the correct
assembly will cause leakage of
gas.
Conversion from LPG to Natural Gas
IMPORTANT
The replacement/conversion of the gas
hob should only be undertaken by a
competent person.
It is important to note that this model is
designed for use with LPG gas but can
be converted for use with Natural gas
providing the correct injectors are fitted
and the gas rate is adjusted to suit.
Replace the rating label (placed near the
gas supply pipe) with the relevant one
for the new type of gas supply. You can
find this label in the package of the
injectors supplied with the appliance.
13
A. Injectors replacement
• Ensure that the gas taps are in the
'OFF' position
• Isolate the hob from the electrical
supply
• Remove all pan supports, burner
caps, rings, crowns and control
knobs.
• With the aid of a 7mm box spanner
the burner injectors can then be
unscrewed and replaced by the
appropriate Natuaral gas injectors
(Fig.1).
Fig. 1
B. Adjustment of minimum
level
When the hob has been fully installed it will
be necessary to check the minimum flame
setting. To do this, follow the procedure
below.
-
Turn the gas tap to the MAX position
and ignite.
Set the gas tap to the MIN flame
position then turn the control knob
from MIN to MAX several times. If the
flame is unstable or is extinguished
follow the procedure below.
-
Procedure:
To adjust the minimum level of the
burners, proceed as follows:
• Light the burner.
• Turn the knob on the minimum
position.
• Remove the knob.
• With a thin screwdriver, adjust the by-
pass screw (Fig.2).
Fig. 2
Minimum adjustment screw
If changing from LPG to natural gas
unscrew about 1/4 turn the by-pass
screw, until a small regular flame is
obtained.
If changing from natural gas to LPG,
completely tighten clockwise the
screw, until a small regular flame is
obtained.
• Finally check the flame does not go
out when quickly turning the knob
from the maximum position to the
minimum position.
This procedure can easily be carried out,
anyhow the hob has been positioned or
built in the working top.
• Repeat the adjustment procedure for
all burners.
14
Electrical Connection
The appliance is designed to be
connected to 230 V monophase
electricity supply.
The connection must be carried out
in compliance with the laws and
regulations in force.
Before the appliance is connected:
1) check that the main fuse and the
domestic installation can support the
load (see the rating label);
2) check that the power supply is
properly earthed in compliance with the
current rules;
3) check the socket or the double
pole switch used for the electrical
connection can be easily reached with
the appliance built in the forniture unit.
The appliance is supplied with a
connection cable and the relevant plug.
The plug has to be fitted in a proper
socket.
If connecting the appliance directly to
the electric system, it is necessary that
you install a double pole switch between
the appliance and the electricity supply,
with a minimum gap of 3 mm. between
theswitchcontactsandofatypesuitable
for the required load in compliance with
the current rules.
Theconnectioncablehastobeplaced
in order that, in each part, it cannot reach
a temperature higher than 90°C.
The brown coloured phase cable
(fitted in the terminal block contact
marked with "L") must always be
connected to the network phase.
15
Remplacement of the voltage
cable
The connection of the voltage cable
to the appliance's terminal block is of
type "Y". This means that its
replacement requires the specific
equipment of a technician. In this case,
only cable type H05V2V2-F T90 must
be used. The cable section must be
suitable to the voltage and the working
temperature. The yellow/green earth
wire must be approximately 2 cm longer
than the phase wires (Fig. 3-a).
To open the terminal block and
reach the terminals, proceed as
follows:
Neutral
Earth
(yellow/green))
Fig. 3-a
Fig. 3-b
insert the point of a screwdriver into
the visible protrunding part of the
terminal block;
exert a light pressure and lift (Fig. 3-
b).
WARNING: The supply cable
replacement MUST only be
carried out by QUALIFIED
PERSONNEL.
16
Building In
SR
SR
TC
A
Fig. 4
Dimensions are given in millimeters
A = Auxiliary burner
SR= Semi-rapid burner
TC= Triple Crown burner
These hobs can be inserted in a
built-in kitchen unit whose depth is
between 550 and 600 mm.
The hobs dimensions are shown in
Fig. 4; the cut out dimensions are
shown in Fig. 5.
The edge of the cut out must have a
minimum distance from the rear wall of
55 mm.
If there are side walls, or sides of the
furniture unit near the hob, the cut out
edges must have a minimum distance of
100 mm.
Hanging forniture units or hoods
must be placed at 650 mm minimum
from the hob.
Fitting the hob to the worktop
Carry out the building in of the hob
as follows:
Fig. 5
1. Place the seals supplied with the hob
on the front edge of the cut out.
17
Then, place them at 11 mm from the
side edges and at 10 mm from the
rear edge, as shown in Fig. 6, taking
care that the seals meet without
overlapping.
2. Place the hob in the cut out, taking
care that it is centred.
3. Fix the hob with the relevant fixing
clamps, supplied with the injectors
kit (see diagram). When the screws
have been tightened, the excess seal
can be removed.
Fig. 6
a
The edge of the hob forms a double
seal which prevents the ingress of
liquids.
Fig.7
a) seal
Possibilities for insertion
Kitchen unit with door
Proper arrangements must be taken
in designing the forniture unit, in order to
avoid any contact with the bottom of the
hob which can be heated when it is
operated. The recommended solution is
shown in Fig. 8. The panel fitted under
the hob should be easily removable to
allow an easy access if a technical
assistance intervention is needed.
Fig. 8
a) Removable panel
b) Space for connections
18
Kitchen unit with oven
The hob recess dimensions must
comply the indication given in Figs. 9
and 10 and must be provided with
brackets to allow a continuous supply of
air.
The hob's electric connection and
the oven's one must be carried out
separately, both for safety reasons and
to allow the oven to be easily taken off
the unit.
Wall units or extractor hoods must be
at least 650 mm from the cooktop (Fig. 5).
Fig. 9
Service and original
spare parts
This machine, before leaving the
factory, has been tested and studied by
many experts and specialists, in order to
give you the best results.
Fig. 10
Any repair work which needs to be
carried out should be done with the
utmost care and attention.
For this reason we recommend that
for any problem you contact the dealer
who sold it to you, or our nearest
authorized Service Centre, specifying the
nature of the problem, the appliance
model (Mod.), the product number (Prod.
No.) and the serial number (Ser. No.)
marked on the identification plate supplied
in the injectors kit.
Original spareparts, certified by the
product manufacturer and carrying this
symbol are only
available at our
Service Centre and
authorized spareparts
shops.
19
3971350.01
05/09 R.A
|